I am now offering a low profile set of reservoirs for the Hornady 366 loader. These reservoirs are 4” shorter than the OEM tubes and offer crystal clear viewing of the contents. Each reservoir is firmly attached to the loader by three cup point set screws and includes a tight fitting cap. The powder reservoir is now available only in the PYREX configuration.
You can safely remove the metering assembly and reservoirs from the loader and invert the assembly to change bushings without emptying the reservoirs.
Shot Reservoir: The reservoir is 4” in diameter and 12” tall. It will hold 25 pounds of shot. The reservoir tube is Acrylic plastic and it is epoxied to its aluminum base. The shot reservoir has an offset mounting to clear the wad guide rod.
Powder Reservoir: The reservoir is 2-3/4” in diameter and 12” tall. It will hold over a pound of powder. The reservoir base incorporates a baffle.
Powder Reservoir: The reservoir tube is Corning PYREX tempered glass. The reservoir base is aluminum. The glass tube and the aluminum base are permanently bonded with epoxy. The PYREX glass tube lets you keep powder in the reservoir for extended periods of time without damaging the reservoir. The PYREX glass tube will never discolor. This is especially important when using corrosive powders like Longshot, TiteWad, Titegroup and 700-X. The PYREX glass tube resists static charge better than a plastic tube.
Shot Reservoir: The shot reservoir has an acrylic tube that is permanently bonded to the aluminum base.
The set of reservoirs is $160.00 plus $20.00 shipping
PM or email me for payment options (check, money order, PayPal)
Got my reservoirs yesterday and got them installed in about 20minutes. Very consistent powder drops.
Very happy with your products. Thank you for a great deal.
Yes, if you pre-order them by letting me know when you want to pick them up. I try to keep them in stock but sometimes that is not possible or I may not be at home.
Just got the bottles for the 366, had them up and running in no time.
Very nice workmanship in both bases and very fast delivery ,packed very good too.
I would recommend Jim and his products any time .
C.W.Croft
Got my reservoirs yesterday and got them installed in about 20minutes. Very consistent powder drops.
Very happy with your products. Thank you for a great deal.
I am now offering a low profile set of reservoirs for the Hornady 366 loader. These reservoirs are 4” shorter than the OEM tubes and offer crystal clear viewing of the contents. Each reservoir is firmly attached to the loader by three cup point set screws and includes a tight fitting cap. The powder reservoir is available in Polycarbonate or PYREX configuration.
You can safely remove the metering assembly and reservoirs from the loader and invert the assembly to change bushings without emptying the reservoirs.
Shot Reservoir: The reservoir is 4” in diameter and 12” tall. It will hold 25 pounds of shot. The reservoir tube is Acrylic plastic and it is epoxied to its aluminum base. The shot reservoir has an offset mounting to clear the wad guide rod.
Powder Reservoir: The reservoir is 2-3/4” in diameter and 12” tall. It will hold over a pound of powder. The reservoir base incorporates a baffle.
There are two options for the Powder Reservoir construction.
Polycarbonate: The reservoir tube is polycarbonate plastic. The reservoir base is aluminum.
PYREX: The reservoir tube is Corning PYREX tempered glass. The reservoir base is aluminum. The PYREX glass tube lets you keep powder in the reservoir for extended periods of time without damaging the reservoir. This is especially important when using corrosive powders like Longshot, TiteWad, Titegroup and 700-X.
The Polycarbonate/Acrylic set is $105.00 The PYREX/Acrylic set is $125.00
Shipping and handling is $20 per set for USPS Priority Mail (lower 48 states). I will accept a personal check, USPS Money Order or PayPal. If you want to do PayPal just PM or email me and I will send you a PayPal Invoice.
I really like the reservoirs I bought... Have you ever considered doing some sort of shut off and allow for the removal of the canister??
1 - 20 of 102 Posts
Trapshooters Forum
A forum community dedicated to Trap shooting enthusiasts. Come join the discussion about targets, clays, hunting, gunsmithing, gear reviews, accessories, classifieds, and more!