Trapshooters Forum banner

Status
Not open for further replies.
1 - 20 of 51 Posts

·
Registered
Joined
·
318 Posts
Discussion Starter #1
JUST RECIEVED 270,000 "NEW" 12 GUAGE TRACER WADS AND ALUMINUM TRACING ELEMENTS.
Available in quanitys of 250 or more @ .12 cents each. Can be loaded in 1 oz., 1 1/8 oz. or 1 1/4 oz. loads depending on the hull you are wanting to use. The 8 petal wad patterns very well for 16 yard shots out to handicap ranges. The visible trace is aprox. 60 yards and can be seen very well in bright sunlight as well as night shooting with any background. A great tool for teaching new shooters where the shot is going in relation to the target or for those expierenced shooters that are having trouble on a perticular post. On January 18th flat rate shipping boxes went up from $9.80 to $10.35 for those of you that have ordered in the past. For ordering or info. contact:
Northwest Research & Development
3431 Wallace Rd. NW
Salem, Oregon 97304
503-999-4617
email [email protected]
 

·
Registered
Joined
·
318 Posts
Discussion Starter #2
Thanks for the order John, hope you enjoy them. Let me know if it helps the kids at your club. Del
 

·
Registered
Joined
·
318 Posts
Discussion Starter #3
Trapperrandy,
I sent you an e-mail. If you don't get it this time, send me a PM here on TS.
Thanks, Del
 

·
Registered
Joined
·
1,038 Posts
Is there a hazmat fee with this? What would be the total cost, including shipping to 05089 for 200?
Thanks...Bruce
 

·
Registered
Joined
·
1,398 Posts
quick question Del, what are these wads colse to in a remington hull, for 1 oz., and 1 1/8 oz??

need to figure a load for clays and greendot, around 1225 fps.



tony
 

·
Registered
Joined
·
318 Posts
Discussion Starter #8
Hello Bruce,
There is no Hazmat fee assosiated with these since the BATF classifid them as a "fuse", because of the less then 2 grains of tracing compound. We ship all quanities up to 500 in USPO flatrate boxes which cost $9.80. For larger quantities we use our own containers and ship UPS or DHL. For 200 the cost would be 200 X .12 = $24.00 + $10.35 = $34.35. Just email me with shipping instructions. We fill the order when we recieve it and ship same day your check or money order arrives.
Mailing address is:
Northwest Research
3431 Wallace Rd NW
Salem, Oregon 97304
503-999-4617
Kind Regards, Del
 

·
Registered
Joined
·
318 Posts
Discussion Starter #9
Hello Tony,
When I use GD I like to use 20 grains for both 1oz and 1. 1/8 loads. In the sts hulls 1 1/8 loads are a little tight depending on what type of loader you use. On my Mec Grabber, with the spring adj. on the shot drop tube it needs to be set almost to max pressure for 1 1/8 but normal for 1 oz. On my PW there is no spring so I just run the wad pin down till I get good crimps. I use this load for anything back to the 27 yd line. I haven't cronographed this load yet, but will and let you know. It seems to shoot up there with my 1oz 1290 loads in STS's and Federal's. I don't quite understand what you are asking about the wads being close to in Remington hulls. Call if you like and we can talk about it. 503-999-4617
Kind regards, Del
 

·
Registered
Joined
·
318 Posts
Discussion Starter #11
Just wanted to say thanks to all those who have ordered our tracers. Hope you enjoy them. Wishing all a nice holiday season.
Del Miesner
Northwest Research & Development
 

·
Registered
Joined
·
318 Posts
Discussion Starter #13
Thanks to Don at the Yucca Knob Shooters Supply for the large order. They have been shipped. Let me know how you like them.
Best Regards, Del
 

·
Registered
Joined
·
318 Posts
Discussion Starter #15
To:
Michael Zakis in PA,
Lonnie Myers in PA,
Joe Baugnet in WI, and
William Hom in CA,

Your orders have been filled and presented for shipment. I imagine shipping will be a little slow this time of year but maybe not. Thanks again and have a enjoyable, safe holiday. Kindest Regards, Del
 

·
Registered
Joined
·
1,398 Posts
these things are slick!


tony
 

·
Registered
Joined
·
318 Posts
Discussion Starter #18
Thanks Tony, glad you liked them. We have lots more when you get'em shot up.
Kind Regards, Del
 

·
Registered
Joined
·
318 Posts
Discussion Starter #19
Thanks to:
Tom Marsala--Lake Ozark MO,

E Barns--Summerville SC,

Joe Nelson--Hazelton ID,
and
George Olsen--Montauk NY,

Your orders have been filled and shipped.

Hope you enjoy them!!

Kind Regards, Del
 

·
Registered
Joined
·
318 Posts
Discussion Starter #20
Thanks to:

J. Garrison your 1000 T have been shipped.

D. R. Frater your 1000 T have been shipped.

R. Baker, your 200 T have been shipped.

M.C. McGee, your 300 T have been shipped.

H. Lekvold, your 200 T have been shipped.

Any questions feel free to call or write.

Thanks again, Del
 
1 - 20 of 51 Posts
Status
Not open for further replies.
Top