1. Attention: We have put together a thread with tips and a tutorial video to help with using the new software. Please take a moment to check out the thread here: Trapshooters.com Tutorial & Help Video.
    Dismiss Notice

Machined Aluminum EZ-FILL Base for Ponsness/Warren

Discussion in 'Jim Skeel' started by skeeljc, Aug 29, 2015.

  1. skeeljc

    skeeljc Supporting Vendor Supporting Vendor

    Joined:
    Aug 27, 2007
    Messages:
    3,816
    Location:
    Terre Haute Indiana
    Machined Aluminum EZ-FILL Base for Ponsness/Warren Loaders

    [​IMG][​IMG]
    [​IMG]

    Now that I have your attention you are probably asking yourself why you should spend $80.00 on a base that will replace the black plastic Ponsness/Warren EZ-FILL base.

    I make a machined aluminum EZ-FILL base with an improved powder seal for the Ponsness/Warren loaders (800, 800B, 800CVT, 900, 950, 2000 and 800 Plus).

    Here are the reasons:

    FIRST: You get a powder seal that works! An o-ring in a groove might make a good seal for a hydraulic fitting but keeping fine grained powders from leaking requires a much different seal design. My seal will work with Hodgdon H110, Winchester 296 and IMR SR-7625. My base comes with two spare seals and detailed instructions on how to remove, replace, and condition the seal.

    SECOND: My base is machined from 6061 T6511 aluminum bar. The surfaces are dead flat. It will not warp or deflect so the seal will always function properly no matter how much shot is in the hopper or how tight you adjust the nylon set screws over the rack. Corrosive powders like Hodgdon Titegroup, Longshot and Lil’gun will not corrode the aluminum base.

    THIRD: There isn’t a big third, just several other nice improvements. The risers are ¼” taller so it is easier to get bushings in and out. The bushing holes have been relocated to improve bushing access. My base comes with Delrin plugs and thumbscrews for the bushing holes. I have added a third nylon set screw to keep the rack properly aligned and prevent it from rubbing against the base at the front.

    My base will work on the 800, 900, 950, and 2000 series loaders.<br>
    (I can install my powder seal in your Patriot - PM me for more information)

    If you want a quality part with improved performance send me an email or PM.

    New Lower Price $80.00 plus $10 shipping.
    Email or PM me for payment information.

    [​IMG]

    If you are having problems with your Patriot I can convert it to my powder seal.
    Email or PM me for more information.

    [​IMG]
     
    Last edited: May 4, 2016
  2. duckey

    duckey TS Member

    Joined:
    Jul 18, 2012
    Messages:
    9
     
  3. duckey

    duckey TS Member

    Joined:
    Jul 18, 2012
    Messages:
    9
    Jim, I have a P/W 800 plus, and would like to buy your EZ-Fill Base, Pyrex Reservoirs.
    Mail:
    Roger Williamson
    1452 N.Vasco Rd. #379
    Livermore,Ca 94551
    925-525-2794
     
  4. duckey

    duckey TS Member

    Joined:
    Jul 18, 2012
    Messages:
    9
  5. skeeljc

    skeeljc Supporting Vendor Supporting Vendor

    Joined:
    Aug 27, 2007
    Messages:
    3,816
    Location:
    Terre Haute Indiana
    Roger, I received your PayPal payment. I will ship your order today via USPS Priority Mail.

    Thanks for the order,
    Jim Skeel
     
Search tags for this page

ponsness warren ez-fill replacement base