1. Attention: We have put together a thread with tips and a tutorial video to help with using the new software. Please take a moment to check out the thread here: Trapshooters.com Tutorial & Help Video.
    Dismiss Notice

Loose 1100 Stock

Discussion in 'Uncategorized Threads' started by timb99, Jun 13, 2007.

Thread Status:
Not open for further replies.
  1. timb99

    timb99 Well-Known Member

    Joined:
    Jan 29, 1998
    Messages:
    7,331
    Location:
    Shawnee, Kansas, USA
    Suggestions, please.

    My daughter's 1100 stock keeps coming loose.

    I'll tighten it pretty firmly, and within 100 shots, it will be loose enough that it can be rotated slightly.

    Not sure what to do.
     
  2. Robb

    Robb Member

    Joined:
    Jan 29, 1998
    Messages:
    827
    Be sure that the {tits} of the first washer down bite into the wood. It is easy to get backword.
     
  3. mt

    mt Member

    Joined:
    Jan 29, 1998
    Messages:
    246
    mine does the same...how many washers should there be...mine has only one if i recall.....it is not a whole circle type but rather is like the circle is cut and the ends are separated a bit.
     
  4. timb99

    timb99 Well-Known Member

    Joined:
    Jan 29, 1998
    Messages:
    7,331
    Location:
    Shawnee, Kansas, USA
    I've got the flat washer with the nibs, (nibs pointing into the wood,) and a lock washer over top of that.

    Tim
     
  5. valmet

    valmet TS Supporters TS Supporters

    Joined:
    Jan 29, 1998
    Messages:
    394
    Location:
    Bemidji, Mn
    i was having the same problem until i wrapped several layers of teflon tape on the threads. took care of the problem for me. good luck. dennis
     
  6. halfmile

    halfmile Well-Known Member

    Joined:
    Jan 29, 1998
    Messages:
    15,643
    Location:
    Green Bay Wisconsin
    The 2 washer system is correct. I tighten mine once or twice a year. A jack handle lug wrench is perfect for the job.

    HM
     
  7. redbearmx15

    redbearmx15 TS Member

    Joined:
    Jan 29, 1998
    Messages:
    30
    timb99.......Try above for picture of stock bolt and the washer's 3 in all #8 #9#10 at the top of the schematic.

    Roger/OH SJVCC
     
  8. timb99

    timb99 Well-Known Member

    Joined:
    Jan 29, 1998
    Messages:
    7,331
    Location:
    Shawnee, Kansas, USA
    Yes, I have all the parts shown. It just keeps getting loose.
     
  9. bigclown

    bigclown TS Member

    Joined:
    Jan 29, 1998
    Messages:
    510
    Hi Tim...the teflon tape sounds like a good idea. I have a wrench built to tighten 1100 stock locking nuts...will bring it with me Thurs. evening to see if it helps. I think our team shoots at like 8:55 pm but I always like to get there early....~ 7:00. Ed
     
  10. mt

    mt Member

    Joined:
    Jan 29, 1998
    Messages:
    246
    thanks...guess i'm putting another order in to brownells
     
  11. ec90t

    ec90t Guest

    Has anyone heard of Loktite? Use the blue and not the red. This will cure your bolt loosening problem privided you have all the proper hardware.

    ec90t
     
  12. timb99

    timb99 Well-Known Member

    Joined:
    Jan 29, 1998
    Messages:
    7,331
    Location:
    Shawnee, Kansas, USA
    Might try the blue loctite or the teflon tape.

    Thanks for the suggestions.

    Tim
     
  13. timb99

    timb99 Well-Known Member

    Joined:
    Jan 29, 1998
    Messages:
    7,331
    Location:
    Shawnee, Kansas, USA
    irfner

    Do you know the thread size?
     
  14. ec90t

    ec90t Guest

    The reason that I said to use the Blue Loktite and not the red is so that you can remove the bolt/nut without heat.

    ec90t
     
  15. timb99

    timb99 Well-Known Member

    Joined:
    Jan 29, 1998
    Messages:
    7,331
    Location:
    Shawnee, Kansas, USA
    ec90t,

    Understood and agreed.

    Tim
     
Thread Status:
Not open for further replies.