1. Attention: We have put together a thread with tips and a tutorial video to help with using the new software. Please take a moment to check out the thread here: Trapshooters.com Tutorial & Help Video.
    Dismiss Notice

F/S: Add-On Ribs for Krieghoff/Kolar and 1100

Discussion in 'Uncategorized Threads' started by skeet_man, Jul 17, 2007.

Thread Status:
Not open for further replies.
  1. skeet_man

    skeet_man Well-Known Member

    Joined:
    Jan 29, 1998
    Messages:
    10,522
    Location:
    Rochester, NY
    Selling some left over add-on ribs from a couple projects. I'm going to list them as I find what I have thats suitable for sale over the next couple days.

    First set are 1/4" tall in steel. These will fit the kolar flat tapered or krieghoff 12mm to 8mm ribs (measure approx .420" at the back and approx .310 @ the front). Ribs are 24 7/8" long, which replicates the factory length from "step" to muzzle on the kolar 30" barrels. Ribs weigh approx 9.7oz each. These are "in the white" as they came off the laser machine. Will need to have the "step" ground, be blued, and have bead holes drilled. These are $40 each plus shipping. I have 4 of these ribs available for sale.

    Pics available upon request.

    More to come.

    email kolarskeet@gmail.com
     
  2. MX3SBOY

    MX3SBOY TS Member

    Joined:
    Jan 9, 2007
    Messages:
    101
  3. skeet_man

    skeet_man Well-Known Member

    Joined:
    Jan 29, 1998
    Messages:
    10,522
    Location:
    Rochester, NY
    Here’s a picture of the steel ribs as posted above:

    <a href="http://photobucket.com" target="_blank">[​IMG]</a>

    Here’s the rest of what I have for sale. They are in various states of use and condition. All are perfectly usable, just some in better cosmetic states than others. Some may need minor straightening as the heat from laser cutting and finishing tends to warp them side to side a little bit. Any listed with bead holes smaller than you’d like, or ribs without holes or holes that aren’t tapped can be changed upon request:

    <a href="http://photobucket.com" target="_blank">[​IMG]</a>

    #1) This one is for the Kolar/Krieghoff, same specs as above for length and width. This one is ¼” aluminum. Very good condition. Has bead holes drilled front and back (#4/40 in the front to accomidate a more secure screw for a hiviz compsight, could always be redrilled and tapped to #6/48, and #3/56 in the middle). Finish is a touch rough, but not bad. Weight is 3.4oz. Price is $60.

    <a href="http://photobucket.com" target="_blank">[​IMG]</a>

    #2) This rib is also for the Kolar/Krieghoff, 1/4", again, same specs. This one also has bead holes front and back, #6/48 for both. Finish was damaged @ some point, so it will have to be stripped off and refinished. Price is $50 for this one.

    <a href="http://photobucket.com" target="_blank">[​IMG]</a>

    #3) This rib is 1/8” aluminum for the Kolar/Kreighoff, same specs for length and width. Bead holes front and back, #6/48 in the front and #3/56 in the back. This was my personal rib for half a year. It still has the remains of the silicone I used to hold it on, which is easily removed w/ a razor blade. Finish is in very good condition. $50 for this one.

    <a href="http://photobucket.com" target="_blank">[​IMG]</a>

    #4) This rib is also 1/8” aluminum, again for the Kolar/Krieghoff, same specs for length and width. This was another of my personal ribs that I used. Finish shows some damage, so it will need to be repaired. This rib comes with a hiviz comp-sight already attached. This rib also still has silicone on it. Bead holes front and back, I believe #3/56 on both. $40 for this one.

    <a href="http://photobucket.com" target="_blank">[​IMG]</a>

    #5) This rib is ¼” aluminum for the Kolar/Krieghoff. This is as it came off the laser machine with no finish. Has bead holes drilled but not tapped front and back. $40 for this one.

    <a href="http://photobucket.com" target="_blank">[​IMG]</a>

    #6) This rib is for the Remington 1100/1187 (approx .305 front to back). This will also work on the Krieghoff 8mm rib. This rib is 1/8” tall and 24” long (replicates the factory step rib over a 28” barrel). Finish is excellent, this rib was never used. Front bead hole drilled but not tapped, no mid bead hole. Price is $60

    <a href="http://photobucket.com" target="_blank">[​IMG]</a>

    #7) This rib is also for the Remington 1100/1187 and Krieghoff 8mm rib. 1/8" thick. As new condition. No bead holes drilled, as it came back from finishing. Couldn’t ask for one better. Price is $70

    <a href="http://photobucket.com" target="_blank">[​IMG]</a>

    #8) Last but not least, a Krieghoff/Kolar 1/8” aluminum rib. Finish is as it came from the factory, front bead hole drilled but not tapped, no mid bead hole. This is the best of my 1/8” Krieghoff/kolar ribs. Price is $60 for this one.

    All prices plus shipping.
     
  4. skeet_man

    skeet_man Well-Known Member

    Joined:
    Jan 29, 1998
    Messages:
    10,522
    Location:
    Rochester, NY
Thread Status:
Not open for further replies.