1. Attention: We have put together a thread with tips and a tutorial video to help with using the new software. Please take a moment to check out the thread here: Trapshooters.com Tutorial & Help Video.
    Dismiss Notice

Eject To Extract change for 90-T

Discussion in 'Shooting Related Threads' started by extrapper84, Aug 5, 2012.

Thread Status:
Not open for further replies.
  1. extrapper84

    extrapper84 Member

    Joined:
    Aug 17, 2011
    Messages:
    337
    Location:
    Rio Rancho, NM
    Looking for a "How-To" on changing a 90T-T over to extract from eject.

    Thanks

    Hal
     
  2. GBatch_25

    GBatch_25 Active Member

    Joined:
    Apr 1, 2008
    Messages:
    2,339
    Location:
    Illinois
    Suggest you email Doug Braker and ask him.

    Try this email: info@dougsgunsmithshop.com

    Or call him:

    Doug's Gunsmith Shop

    3929 8th St SW

    Backus, MN 56435

    218-947-3600


    Gene Batchelar
    Wheaton, IL
     
  3. extrapper84

    extrapper84 Member

    Joined:
    Aug 17, 2011
    Messages:
    337
    Location:
    Rio Rancho, NM
    Thanks, Gene.
     
  4. Ed Pawlus

    Ed Pawlus TS Member

    Joined:
    Jan 29, 1998
    Messages:
    12
    If you haven't found out the information already this is how it is done. Remove the right sideplate. You will see a allen screw about in the middle. Remove it and push out the long rod. This rod is called a Tell Tale rod. Hope this does the trick.....ED
     
  5. extrapper84

    extrapper84 Member

    Joined:
    Aug 17, 2011
    Messages:
    337
    Location:
    Rio Rancho, NM
    Thanks to all.

    I spoke with Doug today, and he is sending me the complete step by step

    instructions.

    He recommends taking parts out of both forearm and from behind the right side

    plate.

    Doug is a great guy to talk to, and he more than "wrote the book" on 90-T.

    Hal
     
  6. GunDr

    GunDr Well-Known Member

    Joined:
    Jan 29, 1998
    Messages:
    2,913
    Rem 90-T......from ejector to extractor

    1- Remove trigger assy.

    2- Remove RH sideplate

    3- Near lower edge of the RH sideplate cut-out, you will find two holes. One will have a roll pin in it,and the other will have a set-screw. This will be the deeper looking hole. Remove this screw using a .050" allen wrench.

    4- With screw removed, the ejector trip rod (the smaller of the two rods) can be pulled from the front of the receiver.

    5- Replace the set screw....so it doesn't get lost. Replace the sideplate and trigger assy.

    *Doing just the above, the ejector/extractor will only rise about 1/8". This is the same distance the ejector/extractor will rise, as if the gun is opened unfired.




    *The following will allow the ejector/extractor to rise the same as if the gun is opened, after it it has been fired. Do not do the following without doing the first 5 steps above, otherwise you will break off the front of the ejector trip rod.

    1- Do the above 5 steps.

    2- Remove forend from gun. The wood does not need to be removed from forend iron.

    3- Located on the top side of the forend iron, near the joint roll (large curved area), you will find a set screw. Remove this set screw using a .050" allen wrench.

    4- Removing the above screw will allow the ejector pivot pin to be slid out of the hole...from left to right. There is no need to remove this pin all the way. Push it out enoungh to remove the ejector sear and it's spring. The ejector sear is the squarish block that pivots in the forend.

    5- Once the ejector sear and spring have been removed, push the pivot pin back into place (flush on each end) and replace the set screw, so it doesn't get lost.

    Keep all of the parts you now have removed in a safe place, and also remember that safe place.

    Doug Braker
     
  7. GBatch_25

    GBatch_25 Active Member

    Joined:
    Apr 1, 2008
    Messages:
    2,339
    Location:
    Illinois
    Now, isn't that just great. The Gun Dr. posts the instructions so no one has to send him their gun, he does the work and then charges them a fee. What a great guy. And I don't even have my 90T anymore. Darn.

    Gene Batchelar
    Wheaton, IL
     
  8. 682LINY

    682LINY Member

    Joined:
    Aug 14, 2006
    Messages:
    967
    some people put more value on friendship than on money
     
  9. Kolar233

    Kolar233 TS Member

    Joined:
    May 10, 2012
    Messages:
    52
    You would have to look long and hard to find a better person than the GunDr.
    Skip Dillin
     
Thread Status:
Not open for further replies.