1. Attention: We have put together a thread with tips and a tutorial video to help with using the new software. Please take a moment to check out the thread here: Trapshooters.com Tutorial & Help Video.
    Dismiss Notice

90-T help....GunDr

Discussion in 'Shooting Related Threads' started by GunDr, Jan 25, 2011.

Thread Status:
Not open for further replies.
  1. GunDr

    GunDr Well-Known Member

    Joined:
    Jan 29, 1998
    Messages:
    2,913
    A few years ago, I wrote up instructions for converting the Rem 90-T from ejecting to extraction. It was a lengthy piece.

    I thought I had saved it on my pc during a system restore but it got lost. I've currently have a shooter looking for instructions and I cannot find them. I know someone had it saved and would post it now and then. If you could once again, I'll highly appreciate it. I don't want to rewrite it all again!!

    Thanks, Doug
     
  2. GunDr

    GunDr Well-Known Member

    Joined:
    Jan 29, 1998
    Messages:
    2,913
    Vern,

    The piece I wrote was a very detailed description of the two options disabling the ejector.

    How did you come up with that thread? I did several diffrent searches and couldn't find anything, other than someone looking FOR an ejector. The thread was not the one I was looking for, but thanks for taking the time to locate it and send it to me.

    Doug
     
  3. Jim_90-T

    Jim_90-T Member

    Joined:
    Jul 14, 2006
    Messages:
    56
    Doug Braker
    Rem 90-T......from ejector to extractor
    1- Remove trigger assy.
    2- Remove RH sideplate
    3- Near lower edge of the RH sideplate cut-out, you will find two holes. One will have a roll pin in it,and the other will have a set-screw. This will be the deeper looking hole. Remove this screw using a .050" allen wrench.
    4- With screw removed, the ejector trip rod (the smaller of the two rods) can be pulled from the front of the receiver.
    5- Replace the set screw....so it doesn't get lost. Replace the sideplate and trigger assy.
    *Doing just the above, the ejector/extractor will only rise about 1/8". This is the same distance the ejector/extractor will rise, as if the gun is opened unfired.
    *The following will allow the ejector/extractor to rise the same as if the gun is opened, after it it has been fired.
    1- Do the above 5 steps.
    2- Remove forend from gun. The wood does not need to be removed from forend iron.
    3- Located on the top side of the forend iron, near the joint roll (large curved area), you will find a set screw. Remove this set screw using a .050" allen wrench.
    4- Removing the above screw will allow the ejector pivot pin to be slid out of the hole...from left to right. There is no need to remove this pin all the way. Push it out enoungh to remove the ejector sear and it's spring. The ejector sear is the squarish block that pivots in the forend.
    5- Once the ejector sear and spring have been removed, push the pivot pin back into place (flush on each end) and replace the set screw, so it doesn't get lost.
    Keep all of the parts you now have removed in a safe place, and also remember that safe place.
     
  4. grunt

    grunt TS Supporters TS Supporters

    Joined:
    Jan 29, 1998
    Messages:
    5,915
    Location:
    Thousand Oaks Ca
  5. GunDr

    GunDr Well-Known Member

    Joined:
    Jan 29, 1998
    Messages:
    2,913
    Thanks Jim, that's the one.

    Doug
     
  6. 9point3

    9point3 Well-Known Member

    Joined:
    Aug 22, 2007
    Messages:
    1,197
    Doug,

    Thanks for the help! Followed your directions and it worked out great


    Jeff
     
  7. 9point3

    9point3 Well-Known Member

    Joined:
    Aug 22, 2007
    Messages:
    1,197
    I didn,t have an issue, I just want to pull em out myself
     
Thread Status:
Not open for further replies.