Trapshooters.com Home Page

Back to the Trap Discussion Web

Wanted: Old style Hornady 366 Legs

Most Recent Posts First

Jump to First Post

Display Deleted Messages

Posted By Posted Date/Time
crab 29-Apr-11 - 06:26 PM ET
Jeff P 30-Apr-11 - 12:05 AM ET
crab 30-Apr-11 - 06:57 AM ET
SPACE GUN 30-Apr-11 - 08:33 PM ET
claykiller 07-May-11 - 06:30 PM ET
claykiller 07-May-11 - 06:32 PM ET
claykiller 07-May-11 - 06:33 PM ET
crab 07-May-11 - 06:46 PM ET
SPACE GUN 07-May-11 - 08:59 PM ET
crab 08-May-11 - 07:25 AM ET


Subject: Wanted: Old style Hornady 366 Legs
From: crab
Date: Fri, Apr 29, 2011 - 06:26 PM ET
Website Address:

You can use any I-beam you can find. Many places throw out short pieces for scrap, or check local scrap yard for some and cut to size,drill 4 mounting holes. Keep in mind this is very small I beam, not the big stuff. You can also heat them up with a small propane torch and spray paint them while hot for a baked on finish.

Email a link to this post - Email a link to this thread

Subject: Wanted: Old style Hornady 366 Legs
From: Jeff P
Date: Sat, Apr 30, 2011 - 12:05 AM ET
Website Address:

How high do you need to get your loader??

I took a piece of 1x6, about an inch longer than the base of the loader is wide. Put that under the loader and drill the holes down through it and through the bench. long lag bolts and washers to bolt it down...it raises the machine about 3/4 of an inch...now my handle clears the edge of the loading table...

Email a link to this post - Email a link to this thread

Subject: Wanted: Old style Hornady 366 Legs
From: crab
Date: Sat, Apr 30, 2011 - 06:57 AM ET
Website Address: http://www.onlinemetals.com/merchant.cfm?pid=13216&step=4&showunits=inches&id=981&top_cat=60

Try the web address I will try to post. You can buy 12" of I beam and cut in half to make 2 riser legs. I think cost is 1.28 per inch. So a little over 15 bucks. Online metals http://www.onlinemetals.com/merchant.cfm?pid=13216&step=4&showunits=inches&id=981&top_cat=60

Email a link to this post - Email a link to this thread

Subject: Wanted: Old style Hornady 366 Legs
From: SPACE GUN
Date: Sat, Apr 30, 2011 - 08:33 PM ET
Website Address:

I have a set ours for shipping cost Check your P/M

Email a link to this post - Email a link to this thread

Subject: Wanted: Old style Hornady 366 Legs
From: claykiller
Date: Sat, May 07, 2011 - 06:30 PM ET
Website Address:

Hey Crab, thanks for the tip on online metals. Ordered 12" I-beam cut it in half, drilled the proper holes, then painted. Here is what I ended up with and they work awesome:

Email a link to this post - Email a link to this thread

Subject: Wanted: Old style Hornady 366 Legs
From: claykiller
Date: Sat, May 07, 2011 - 06:32 PM ET
Website Address:

Hey Crab, thanks for the tip on online metals. Ordered 12" I-beam cut it in half, drilled the proper holes, then painted. Here is what I ended up with and they work awesome:

Email a link to this post - Email a link to this thread

Subject: Wanted: Old style Hornady 366 Legs
From: claykiller
Date: Sat, May 07, 2011 - 06:33 PM ET
Website Address:

Hey Crab, thanks for the tip on online metals. Ordered 12" I-beam cut it in half, drilled the proper holes, then painted. Here is what I ended up with and they work awesome:

Email a link to this post - Email a link to this thread

Subject: Wanted: Old style Hornady 366 Legs
From: crab
Date: Sat, May 07, 2011 - 06:46 PM ET
Website Address:

Glad I could help but it looks like you now have a flinch......perhaps a release trigger style keyboard ?

Just kidding, couldn't help my self.

Email a link to this post - Email a link to this thread

Subject: Wanted: Old style Hornady 366 Legs
From: SPACE GUN
Date: Sat, May 07, 2011 - 08:59 PM ET
Website Address:

I was just wondering, What was the shipping cost on the metal? I shipped two three inch I beams four inches long and it cost me a little over ten bucks

Email a link to this post - Email a link to this thread

Subject: Wanted: Old style Hornady 366 Legs
From: crab
Date: Sun, May 08, 2011 - 07:25 AM ET
Website Address:

For the online metals I am pretty sure the shipping is there in the cart at checkout. Depends on method of shipping and what you order. Aluminum is much lighter and works just as well for riser legs-and easier to drill the holes in.

Claykiller I sent you a PM

Email a link to this post - Email a link to this thread

The owners, administrators and moderators of the Trapshooters.com have no obligation to keep objectionable messages off this forum. It is impossible for us to review all messages. All messages express the views of the author, and neither the owners, administrators or moderators of Trapshooters.com Discussion Forum will be held responsible for the content of any message. The owners, administrators and moderators of the Trapshooters.com Discussion Forum reserve the right to remove, edit, move or close any thread for any reason at our sole discretion. However, the owners, administrators and moderators are not monitoring or editing the site and are under no obligation to police it for items that some persons may find objectionable.

[ Back ]

To Register for full access to reply and create threads Click Here!
To Login to the discussion web Click Here!
To report problems with this site email email us